RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08
Hydraulic pick-up sweeper for tractor

Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
  • Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
  • Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
  • Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
  • Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)
  • Hydraulic pick-up sweeper for tractor (RTH24-05 / RTH24-06 / RTH24-07 / RTH24-08)

Brush Drive

  • Requires 16 GPM at 2000 PSI (60 LPM at 138 bars) for a recommended brush speed of 150 RPM
  • Brush speed is controlled by the equipment engine speed
  • Powered by single orbital motor mounted to the core of the brush
  • Third valve is required to operate the brush, a fourth valve is required to operate the hydraulic angle change and a fifth valve is required to open or close the upper
  • Hydraulic hoses that supply the third valve of the equipment must be 3/4" inside diameter

Brush

  • Choice of poly or poly / wire bristles

Open / close upper

  • 2 hydraulics cylinder 1 1/2" diameter to opening the upper 90░ (without remove the upper)
  • Hydraulic hoses with quick coupler to hook up to the fourth valve
  • 0.6 cubing yard

Mechanical Components

  • Pressure to the ground is controlled by the weight of the brush
  • Shock absorbers to reduce brush hopping
  • The brush is mounted on two 1 3/4" (45 mm) diameter flange bearing
  • Stopper to protect the shock absorber
  • Anchor rings for handling and transportation
  • Storage stands
  • Heavy duty motor safety guard
  • Install on the three points hitch cat.2
  • 16.5- 8 diameter rear caster wheel

Frame

  • 90% of the parts are laser cut, cross member are heavy duty rectangular tubing
  • 16 gauge steel hood covering 180░ of the brush
  • All main parts of the frame, including the hood, are bolted together for a quick replacement
  • 1 1/2" (38 mm) diameter pivot axle for the angle device

Finish

  • All parts are sandblasted individually
  • Coat of epoxy primer and polyurethane top coat

OPTIONS

  • Hydraulic angle change with 2" diameter hydraulic cylinder
  • Hydraulic hoses with quick coupler to hook up to the fourth valve (if available)
  • 150 or 200 gallons water tank with support to be mounted directly on the quick attach
  • 12 volt electric water pump and hardware
  • 4 spray nozzles mounted into the hood for a direct watering of the brush
  • diverter valve for hydraulic angle
  • P.T.O pump 16 gpm
  • Medium travel spring
  • Gutter broom on the tractor